WISEDENT is an experienced dental equipment & dental handpiece manufacturer over 10+ years.
Language
WISEDENT is an experienced dental equipment & dental handpiece manufacturer over 10+ years.
The modern dental high speed handpiece is, nowadays one of the most important tools used in dental practice. They wear and tear as all mechanicals do. Now, take a situation, which probably many may experience or at least heard someone experience; here is one case. The knowledge of common repair techniques will allow dental professionals to keep their handpieces in proper shape to continue performing at the level necessary for patient care. This article addresses some of the easy ways to correct common problems on high speed dental drills. Let's start keeping these important tools running!
The knowledge of when a dental high speed handpiece has failed would allow it to be corrected and used again, which is essential for the patient's safety and performance. Common signs that might indicate a faulty handpiece include the following:
Unusual Noise: A grinding or rattling sound coming from the handpiece indicates worn bearings or something is wrong inside. Check periodically.
Reduced Speed: If the motor or air supply is a problem, a noticeable drop in rotational speed during use.
Power Intermittent: When the handpiece turns on and off randomly or has power but it's not steady, it could need some work.
Constant Vibration: The handpiece vibrates excessively due to imbalance or damage.
It Heats Up: This means friction or lack of lubrication when the handpiece feels too hot to hold during operation.
Poor Water Spray: It causes the inability to cool down in procedures. If it is not able to provide adequate and evenly distributed water spray, then it is because of blockages or malfunctioning components.
Attachment of Burs is a Problem: If the burs are difficult to insert or remove, it may be a problem with the chuck mechanism.
Air Leaks: According to experts, any hissing or whistling sounds could mean air leaks that would hurt performance.
If your high-speed handpiece does turn off while in use, you are required to switch it off immediately to avoid unsafe handling. Here is what you should do:
Stop Using the Handpiece: Stop using it immediately if further damage is being caused to the handpiece or if the patient is harmed.
Check the Air Supply: Make sure the handpiece has an air compressor supplying the air. Look for blockages in the airline or connections that may block airflow.
Inspect the Connection: Connect the air hose very tightly to the handpiece. A loose fit would result in a loss in power. Always unhook and rehook it once again for a tight fit.
Check the Turbine: Remove the handpiece. If it can be unscrewed from the handpiece, take an even closer look at the turbine itself. Check the buildup of dirt or possible damage. Replace if so or clean.
Lubricate it: Make sure the handpiece is kept well lubricated. Without lubrication, there may be friction and loss of power. All manufacturers have their specific techniques for proper lubrication of the handpiece.
The main problems the patient faces in procedures as well as care when their dental high speed dental drill won't spin are that it causes significant troubles. Here's how to solve this problem:
Stop Using at Once: The handpiece must be turned off to avoid damage and to remain safe.
Check Air Supply: Check if the air compressor is running and if there is suitable pressure. Check the airline for blockages or leaks.
Inspect the Connection: Ensure that the handpiece is tightly connected to the air source. It should be correctly connected; thus, you need to disconnect and reconnect.
Are you using a dental high speed handpiece that isn't spraying water? Check out some troubleshooting tips for such conditions. Read and follow through with the following procedures the moment the incident occurs.
Inspect the Water Supply: Check if the tank of water is full and that the water line is not blocked.
Check on the Connection: Ensure that the water supply as well as the handpiece is tightly connected. Water flow cannot be possible when one connection is loose.
Ensure to Remove Blockages: Check on the water spray nozzle, you might find some debris within. Gently brush away from debris with a small-sized wire or brush.
Balance the Water Pressure: Ensure that the pressure of the water is in the right range. The lower pressure may hinder the sprayer's function.
Like any tool, the proper maintenance needed for dental handpieces helps prolong its use and obtain great performance. Here are common mistakes to be avoided.
Neglecting Regular Cleaning: Buildup and decreased performance can result from failing to clean the handpiece after each use. Always clean properly with preferred materials.
High-speed handpieces: If you use too much lubricant, you’ll attract debris and end up with blockages. Use lubricant as directed by the manufacturer. Follow the instructions to let the handpiece work smoothly.
Ignoring Signs of Wear: Ignoring strange sounds, or strange performance, may lead to more serious problems. Take care of any malfunction signs and report them as soon as possible.
Inadequate Storage: Handpieces can be damaged if stored improperly. Store them in an appropriate storage solution to protect them from dust and impacts.
Skipping Professional Servicing: Don’t try to solve complex problems on your own. But regular servicing by a technician can extend the life of your handpieces.
We have discussed how important it is to keep dental high-speed handpieces working for good dental care. We covered how to find problems like strange noises, loss of power, or water spray problems. We also pointed out some common mistakes to avoid, such as forgetting to clean or using incompatible parts. WISEDENT is the best dental high speed hand piece because it supplies you with reliable tools that enable you to deliver great care to your patients. Don’t forget to their official website for modern dental high speed dental drills.
